Alpine imprint sound manager software download

#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD INSTALL#
#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD DRIVER#
#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD PC#
#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD SERIES#

#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD DRIVER#

Move the Microphone to the front left corner of the driver seat *Notice: Reduce the height of the Mic to shoulder height 2) Exit the Vehicle - Close ALL Windows and Doors 3) Double-click вЂMeasureвЂ™ to begin measuring Position 4. 2) Exit the Vehicle - Close ALL Windows and Doors 3) Double-click вЂMeasureвЂ™ to begin measuring Position 3. Move the Microphone to the co driver side Listening Position Notice: Place the microphone at normal ear height, centered approximately 5,0 cm in front of the headrest position. Move the microphone to the rear center Position NOTE: Place the microphone at normal ear height, centered approximately 5,0 cm in front of the headrest position. ItВґs not a problem to make a measurement without a rear system. The chirp starts very quiet and gets louder and louder Chirp Order: 1,2,3,4,5,6 1 2 4 3 5 6 When the first measurement is You can read which speakers are detected.

#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD SERIES#

The measurement starts: Notice: You should hear a series of Logarithmic Chirps coming from each speaker: Driver seat front, passenger seat front, passenger seat rear, driver seat rear, and then sub left and right. The software shows always the status and the options. And the software will check which speakers are connected as well. There will fixed the levels crossovers, gains, timedelay. *Notice: Microphone MUST be pointing straight up 2) Exit the Vehicle and Close ALL Windows and Doors.Дouble-click вЂMeasureвЂ™ Notice: The first measurement takes a long time, approximetly 10 minutes.

Place the microphone in the DriverвЂ™s Listening Position Notice: Place mic at normal ear height, centered approximately 5,0 cm in front of the headrest position. That means the timedelay will be set for this position. Select which area is your prefered listening position by double click.

#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD PC#

In this case.silence is golden.ДЎ2 Step 8.1 вЂ“ Start the latest Program Version 2.10Д¬onnect the PXA-H100 to your Computer Start PC Programm Select PXA-H100 Close the doors, windows and sunroof while measuring. Stop the engine, switch the air-condition and the fan off. 2) Attach the microphone to a camera tripod, using the pre-threaded nutsert Notice: Make sure the microphone is connected to the PXA-H100ДЎ1 Keep silence Notice: The measurement area must be absolutely quiet. In case the car is equipped with active headrests, don't attempt to remove them. *Notice: The measurement results may improve when the front headrests are removed before measurements. If speakers are installed in the door empty the door compartment. Please contact your local Alpine support for details.Д© Step 6 - PC Setup ItвЂ™s now time to connect your PC via USB Requires: PC with Windows XP (with any or no service pack) IMPRINT Sound Manager software installed included USB to Mini USB cable When the microphone is connected with the PXA-H100 the HU will show the message вЂњMultEQ Setting Mode DonВґt touch any buttonвЂќДЎ0 Step 7 - Preparing the Vehicle & MicrophoneДЎ) Ensure that all seats are in the proper position for the driver.

#ALPINE IMPRINT SOUND MANAGER SOFTWARE DOWNLOAD INSTALL#

Install IMPRINT Sound Manager Software If necessary install the USB- drivers Requires: PC with Windows XP PXA-H100 Setup Disc V2.10 2m USB to Mini USB cable *Notice: although Windows Vista has not been officially approved by Audyssey Labs, it will work in most cases. 200Hz) If subwoofer Subsonic Filter cannot be turned off then select the lowest frequency setting (eg. Setting of the PXA-H100ДЎ) Set Amplifier Gains: Front & Rear = 1/2 gain Subwoofer = 1/4 gain 2) Turn all Amplifier Crossovers вЂ™OFFвЂ™ Allow the PXA-H100 to Set the correct Crossovers for the best Sound Quality NOTES: If subwoofer Low-Pass Crossover cannot be turned off then select the highest frequency setting (eg. The Front and Rear System passive powered by a 4 channel amp and one mono amp for the sub. Pre IN: Front, Rear Pre Out Sub Setting of the PXA-H100: That means the Pre Outs Front and Rear are changed to Pre Ins. When the system switch of the HU is in the вЂћEQ/DIVвЂњ position you can use the integrated amplifier of the Headunit. Notice: When the system Switches are fixed in the вЂћEXT APвЂњ (External audio prozessor) Position, the Pre OUTs Front and Rear are changed to Pre INs. You can use the internal Amps from all вЂћIMPRINT ReadyвЂњ Headunits when the PXA-H100 is connected. Notice: This setting works not precise with MultEQ Typical System: You can do the calibration with MultEQ. Setting `X-Over` DIP-switch `Front/Rear/Sub` When you have a 3-way system calibrate the system manually with the вЂћBass EngineвЂњ.

RCA Outputs for Front, Rear and Subwoofer Guide Input for the navigation System Power Connector Connector for the microphone Ai-Net connection from the Headunit to the PXA Ai-Net Connection when you use a CD-Changer for example USB Connection to the PC PXA-H100 IMPRINT Audio Processor PC Setup & Tuning

Alpine imprint sound manager software download